2 Ohm Stable
The lowest impedance accepted by this amplifier is 2 ohms. Amplifiers that are 2 ohms stable produce more power resulting in more volume. This amp can comfortably power speakers or subwoofers with all channel(s) being used at a load of 2 ohms.
Bridging an amplifier means to combine channels of a multi-channel amplifier to get more power or flexibility out of it. For instance, on a 4 channel amp, channels 1 and 2 could be used normally for your speakers, and channels 3 and 4 can be bridged for more power to a single subwoofer. A 2 channel amp can also be bridged to power a single subwoofer.
Class A/B amplifiers have long been known for their ability to produce great quality sound while performing more efficiently than pure Class A amplifiers. We have developed a specific linear circuitry that further reduces distortion while increasing both sound quality and power output.
High and Low Level Inputs
An amplifier with both high-level and low-level inputs provides flexibility by allowing you to build an audio system using virtually any standard factory or aftermarket source unit. High-level (speaker level) inputs accept the signal from the speakers, while low-level (RCA) inputs accept the signal from the pre-amp outputs of the source unit.
MOSFET stands for Metal Oxide Semiconductor Field-Effect Transistor. MOSFETs are used either as a switch or to amplify a signal. MOSFETs are superior to other FETs, because they require less current to operate, which makes them better suited for car audio.
Multi LED Back Lit
Multiple LED Backlighting gives this Phantom Series Amps an awsome red glow when the amp is turned on.
If the amplifier gets too hot, the thermal protection circuit turns the amp off and allows the amp to cool down before turning it back on. If a speaker fails causing an electrical short, the protection circuit will automatically cut the output and remain in that state until the short is resolved. These safety features give you peace of mind knowing the amplifier is constantly monitoring conditions to protect itself.
Subwoofer Level Control
The ability to boost or attenuate the sub level when an amp and subwoofer are connected to the subwoofer pre-amp output.
Switchable Input Sensitivity
Switchable Input Sensitivity gives you the freedom to connect the amp to any standard source unit and have peace of mind it will be within range to properly match the output of the source unit allowing you to use the volume controls on your source unit the way it was designed.
Variable Bass Boost
Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
Variable Gain Control
Variable Gain Control lets you balance the amps output with the speakers or subs the amp is driving. To much gain will lead to distortion and to little will lead to clipping.
Variable High Pass Filter
Variable high-pass filter gives you control over the frequencies that pass through to the full range speakers.
Variable Low Pass Filter
Variable low-pass filter gives you control over the frequencies that pass through to the subwoofer.
|channel configuration||4/3/2 Channel|
|frequency response||9 Hz to 50 Khz+/-1 dB|
|input sensitivity switch||Yes|
|subwoofer level control||Yes|
|bass boost||Variable 0 to 18 dB|
|high-pass filter||Variable 50 Hz Hz to 250 Hz|
|low pass filter||50 Hz to 250 Hz|
|high level inputs||Yes|
|rca inputs||4 Channel|
|s/n ratio (a-weighted)||103 dB|
|power supply type||Mosfet Power Supply|
|channel separation||90 dB|
|t.h.d. (total harmonic distortion)||0.01 %|
|speaker impedance||2 to 8 Ohms|
|rms power @ 4 ohms||244 Watts X 4|
|bridged rms power @ 4 ohms||975 Watts X 2|
|rms power @ 2 ohms||488 Watts X 4|
|bridged power @ 4 ohms||1300 Watts X 2|
|peak power @ 4 ohms||325 Watts X 4|
|peak power @ 2 ohms||650 Watts X 4|
|total power output||2600 Watts|
|amp topology||Full Range, Class A/B|